Review article of Martin Lenz, Locke's Sprachkonzeption, Berlin: de Gruyter, 2010.

Electrochemical assisted abrasive flow finishing is a newly developed hybrid finishing process which is used to finish the internal parts of work piece having complicated geometry to large extent. In electrochemical assisted abrasive flow machining higher abrasion of the material was detected due to the combine effect of ECM and AFF processes. In Electrochemical aided abrasive flow machining a electrolyte is added to the prepared media .This media consist a kind of polymeric carrier and abrasive particles that are hydrocarbon gel, (...) Al2O3, Silicon based polymer, and NaI Sodium iodide as electrolytic salt. In this experimental research different process parameters such as voltage, abrasive concentration, Number of cycle, molal concentration and diameter of rod were considered at different levels for response characteristic of surface roughness Ra and material removal MR based on Taguchi method using standard L27 orthogonal array OA for the plan of experimentation. To determine the contribution of each parameter analysis of variance was used. Sandeep Singh | Sunil kumar "Experimental Research Work to Optimize Process Parameters into Electro Chemical Abrasive Flow Machining using Taguchi Methodology" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-4 , June 2017 . (shrink)

Among all non conventional micro machining, electrochemical discharge machining ECDM is having high quality of material removal rate with zero residual stress. This machining has been accepted as a highly modern technology in micromachining. In this paper an effort has been done on micro drilling of glass using electrochemical discharge machining ECDM . A fixed tool and a step down transformer have been used to support the steady machining to increase the accuracy of work piece. The input parameters used in (...) this experiment are voltage, concentration of electrolyte, enter electrode gap and ratio of area of electrode. MRR has been investigated over the input parameters. Feed rate and electrolyte temperature has been made constant of 3µm sec and 30°c respectively. Taguchi method is used to optimize the effect of the process parameters on MRR. The signal to noise S N ratio and the ANOVA analysis are employed to find the contributions of input parameters. Vikrant Sharma | Sunil Kumar "Experimental research to Optimize Process Parameters in Machining of Non Conducting Material with hybrid non conconventional machining" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-4 , June 2017. (shrink)

Do minds and ideas connect, interact, or even depend on each other, and if so, how exactly do they connect and interact? How should we conceive of the mode and process of minds and ideas being in a network and connected in some way, that is, being intersubjective or social? Martin Lenz's study Socializing Minds convincingly shows that, contrary to widespread opinion in philosophy of mind, at least some early modern philosophers, here Spinoza, Locke, and Hume, actually give a (...) positive answer to the first question and present models that respond to the second question, thus addressing what Lenz proposes calling 'the contact problem' and repudiating the idea that mentalism is necessarily bound to individualism. In this comment, I focus on a detail in Lenz's reconstruction of Spinoza's 'metaphysical model' of the intersubjectivity of minds, namely the Aristotelian physical dynamism that would underlie Spinoza's idea of the interaction of minds. While I agree that Spinoza's model of interaction of minds refers to the Aristotelian conception of motion, I argue that the guiding principle in natural motion is best understood not only in terms of contrariety but also in terms of complementarity. Admittedly, my proposal goes beyond Spinoza's model of ideas in contact, and probably beyond Lenz's interpretation of that model, but it might enrich the imagination of the socialising of minds and ideas from a kinetic point of view, which, at least as I understand it, is precisely what Spinoza and Lenz thrive on. (shrink)

Kant and Medicine - the Philosopher as Anthropologist, Physician and Patient. It remains uncertain whether the student Immanuel Kant (1724-1804) truly wanted to become a physician or only said this in order to please a sponsor. Due to his narrow chest and other typical weaknesses of a scholar he considered himself a hypochondriac and cautiously kept his distance from dangerous illnesses, especially those of the mind. He inspired his students - including Herder, Herz, Lenz and Hoffmann - far less (...) with logic and metaphysics than with exciting findings about far away countries, their alien inhabitants and the health dangers lurking in exotic parts of the world. He called for philosophical treatment of physical illnesses beyond the limited "veterinary" approach of medicine. He claimed the responsibility of the philosophy faculty for forensic questions. Kant developed original ideas about the seat of the soul, which led to the construction of a first model of the brain including functioning synapses. He was unable to overcome reservations about smallpox vaccination because he feared a change in the germ line. He wanted to see "how long the stuff would last" and during his later decades used all the classic dietetics to successfully extend his life. These sex res non-naturales continue to play a significant role in the prevention of widespread diseases today. Then an "electric revolution of the air strata" took its toll on him. Towards the end, his confidants were to look at him like a child, who, however, left posterity an extensive work with deep insights into his thinking, the Opus postumum. (shrink)